This post continues my story about the desktop version of LXmini speakers that I have built and set up on my computer desk in a somewhat unusual way:
So, why are the speakers are "toed out"? The idea is that since the full range driver has a dipole dispersion pattern, if we turn it outwards, then the null of the dipole becomes directed towards the opposite (ipsilateral) ear, thus naturally contributing to the suppression of the acoustic cross-talk between speakers. This effect these days is usually achieved using DSP by injecting a suppressing signal into the opposite speaker (see a great post by Archimago and STC on this topic). However, it would be nice if the opposite ear would be just naturally blocked hearing the sound from the speaker.
I've estimated the angle between the full range driver and the opposite ear to be approximately 75°, thus the suppression is not maximal. However, it should still add extra -5 to -10 dB attenuation to head shadowing, depending on the frequency. I plan to measure the exact attenuation profile some time later. Another feature of setting the speakers this way is that the back of the speaker gets farther from the back wall, at about the recommended minimum of 1 meter.
Ideas for Tuning
Since the original LXmini tuning was aimed to achieve flat response on-axis (see the design notes), my unusual speaker arrangement required a dedicated tuning. I started looking around for ideas on to achieve close to ideal response in the time domain.
The author of Acourate Dr. Brüggemann holds a very strong position on using linear phase crossovers. Acourate can generate various kinds of crossovers, both in minimum phase and linear phase versions. Also, there are some tools (including a new one added in the recent Version 3) which are intended to bring each driver as close as possible to the corresponding band pass filter of the crossover, both for amplitude and the phase. Together with proper time alignment of the sound from each driver at the listening position, this allows to achieve "ideal" summing of the acoustic crossover components, yielding the perfect Dirac impulse response for the speaker as a whole.
Though, my initial concerns were about the pre- and post-ringing behavior of the linear phase filters. As we know, they are symmetric around the center, and the pre-ringing may potentially exceed the thresholds of masking. When the components of a linear phase crossover sum up as intended—with their peaks coinciding, the pre- and post-ringing components from each crossover band cancel each other. However, if there are time shifts—even as small as a fraction of a millisecond—this does not happen. The example below is for a two-band linear phase Neville Thiele crossover:
This is how the summed impulse response looks like on the logarithmic scale when the components are properly time aligned, and also for 0.23 ms and 0.5 ms time of arrival difference:
The red vertical line is the ideal IR which occurs in the ideal time alignment case, and on the right are the IRs when one of the crossover components is shifted. Recall that these delays correspond to a distance difference of just about 7.88 cm and 17 cm—that's comparable to the size of the human head.
When I started discussing this topic on the Acourate forum, one of the members has pointed me out to the white paper by B. Putzeys and E. Grimm on their ideas behind the DSP-based implementation of the professional Grimm Audio LS1 speaker (which costs quite a lot!). The authors used a minimum phase Linkwitz-Riley filter, but compensated for its phase deviations using an inverse all-pass filter. If we think about this approach, it effectively also yields a linear phase filter. In fact, when crossover components get time shifted, the combination of the crossover plus reverse all-pass filter also exhibits pre-ringing, although its level is a bit lower, and what's more important, the duration is shorter:
(Note that the red IR is not an ideal Dirac pulse because although the phase response of the all-pass filter I created is close to the phase response of LR4, it is not exactly the same). However, these improvements over the ringing of the Neville Thiele crossover are just due to the fact that the LR4 crossover has more relaxed slopes to start with:
Thus, instead of compensating for phase deviations of a minimum phase crossover, which can be quite severe for high order crossovers, we can as well just start with linear phase crossovers as they are much easier to work with. For example, I wanted to use an asymmetric shape in which the higher frequencies driver has more relaxed slope compared to the lower frequencies driver. This is beneficial for the LXmini design because the directional pattern of the full range driver yields more precise spatial cues than the omnidirectional woofer. This approach also helps for the pair of the woofer and the subwoofer because I only have one, so I would like to experience a stereo bass as much as possible. The asymmetric shape of crossover slopes at first yields a non-flat summed frequency response, however this is easy to compensate (again, with a linear phase filter), thanks to the fact that the phase shift, being always equal to zero, does not affect the summing of amplitudes of the crossover components.
Another interesting observation. The fact that I'm performing the tuning in a real room, not in an anechoic chamber, implies that I need to use windowing of the measured frequency response. As I have realized after brief experiments, the frequency dependent windowing (FDW) partially suppresses pre- and post-ringing of linear phase filters. However, as a result it also changes the shape of its frequency response by making it less steep. In my opinion, this is a good trade-off. In the next section I will show the shapes and IRs of the linear phase crossovers I have ended up with.
Crossover Preparation Details
The aforementioned Grimm Audio LS1 white paper has a suggestion on "ideal" crossover points. From the psychoacoustics data, the authors state that the directional pattern of the frequency response should be used down to 300 Hz. The original LXmini has its acoustic crossover point closer to 790 Hz, however it uses a 2nd order LR crossover thus the output from the full range driver actually goes quite low in frequency range. So the first thing I've done was to measure the raw response of the full range driver. Here it is together with an FDW processed version:
Looking at the natural roll-off of the driver I have chosen 366 Hz as the crossover point. At the high frequency end, the full range driver due to its relatively large size starts working in a breakup mode, thus losing efficiency. Plus, I'm not listening to it on-axis and that creates a natural roll-off at high frequencies. However, that's not a problem. Since the speakers are located quite close to my ears, there is no need to try to make the frequency response to be ruler flat at the high frequency end because that makes the sound too harsh. So I generated a LR2 linear phase crossover for 11 kHz and used its low frequency part to taper the response of the driver on the right side. This is how the final crossover component looks like, overlaid with the raw windowed response:
Similarly, for the woofer driver I have chosen 46 Hz as the crossover point. The slope on the left side is LR4, however on the right side I used Neville Thiele 1st order crossover as it has a sharp, "brick wall" slope. I passed it through the same frequency dependent window that I use for the in-room measurements, and this has made the shape of the slope more "relaxed". Below for comparison are the original NT1 slope overlaid with a windowed one:
There is not much difference in the time domain though:
And this is how the designed crossover component looks on top of the raw driver response:
The subwoofer was a bit interesting. Choosing the crossover did not require any thinking because the crossover point was already set from the woofer driver, and the type on the right side is also Neville Thiele 1st order. However, since it's an active subwoofer with servo (Rythmic F12G), it has some settings of its own. I experimented with different damping settings and low-end extension, and found that low damping and the extension down to 14 Hz creates a time domain response which looks close to the IR of the crossover if I invert its polarity. This is how these IRs look like overlapped (the polarity IR of the subwoofer is inverted):
And this is the final look on the crossover components that sum up into a flat frequency response (with the high frequency range trimmed down) and a zero phase response:
Visually this crossover reminds of the Bessel low-pass filter (used in the "RBessel" crossover type in Acourate) of a high order, however mine uses even steeper slopes on rights sides.
Driver Tuning Process
My tuning process has two major stages: the first to bring each driver as close as possible to the behavior of the corresponding band pass filter of the crossover (that also includes fixing the phase behavior), and the second stage is to combine these drivers into a proper acoustic crossover.
I was doing all the measurements from the single position—the listening position. Although it is possible to linearize drivers in the near field, I did not use this approach due to two reasons. First, the full range driver works as a dipole, and they must be measured from some distance. Second, since I was interested in the performance of the crossover at the listening position, this was the natural position to use for driver linearization as well.
For the driver linearization I used the "Room Macros" of Acourate, setting the "Target Curve" to be the desired crossover band pass behavior. Obviously, I used the same window for the FDW of the measured driver response as the one I used to process crossover parts during the preparation stage. I did not use "Psychoacoustic" smoothing at the driver linearization stage, instead I used more technical "1/12 Octave" smoothing. I was also limiting the amplitude correction to avoid creating a boost at the frequency bands where the response of the driver was naturally decaying below the intended crossover suppression level. As an example, below is the correction filter for the woofer driver, overlaid with the target:
After the correction filter has been generated by "Room Macro 4" and the result has been evaluated via a test convolution, I re-measure the driver with the filter applied. Then I check the phase behavior. Since the correction process of Acourate tries to bring the driver to the minimum phase behavior, it will leave out phase deviations that present in the minimum phase impulse response of the target curve. Note that when equalizing an entire full-range speaker to a mostly flat target curve, these phase deviations will end up outside the hearing range. However, for a driver, since it has a limited frequency range the phase deviations will typically end up near crossover frequencies, and this fact will make proper time alignment more problematic. For example, this is the phase response of the corrected woofer:
We can see that the phase gradually deviates from zero and "flips" over the 180° angle at 47 Hz. I treated these phase deviations using the same approach as in the Grimm Audio white paper, which are in essence the same approach as the one described by Dr. Brüggemann in his post "Time alignment of drivers in active multiway speaker systems" on the Acourate forum. That is, we need to "guess" an all-pass filter which has a similar shape as the form of the phase deviation of the speaker, and then put its reversal into the correction chain (that effectively means, we need to convolve the reverse all-pass filter with our existing filter). For example, for the woofer the corrected phase behavior looks like this:
Obviously, since it's an all-pass filter, the amplitude remains the same. There shouldn't be more than 1 or 2 all-pass corrections needed. Only the area within the driver working range must be corrected, and we must look at the windowed response to avoid correcting for the effects from reflections that very dependent on the mutual distances between the driver, the reflecting surface, and the measurement point.
Now with each driver being brought as close as possible to the desired crossover band-pass filter behavior, we need to "assemble" them into a speaker by aligning their levels and times of arrival. To do that, first I measured the speaker as is, and did a rough correction of driver levels. Then I used the the sine wave convolution approach first for aligning the full range driver with the woofer, and then the woofer with the subwoofer. At low frequencies, the convolved sines may initially be considerably shifted from each other. Also, the low frequency filter may be developing a bit slowly and have irregular sine amplitudes in the beginning. To ensure that the resulting time alignment of the drivers is proper, I had applied the same sine wave convolution step to the crossover components and used the produced overlapping picture as a reference. For example, this is how the sine waves of my crossover look like for the 46 Hz point:
And this is how the results of sine wave convolution was looking initially for the woofer and the subwoofer:
Compared to the image before, it becomes obvious that the subwoofer (the blue curve) needs to be shifted ahead in time of the woofer for a proper alignment.
After applying gains and delays to the driver filters, I have made another measurement and double-checked that the sine convolution on the measured IRs produces the expected result.
Target Curve Adjustments
Life would be too easy if we could just take the summed crossover response and use it as a target for the overall speaker tuning. I tried that first and was not impressed with how it sounded. The first problem was that the vertical positions of virtual sources were too high while I would prefer having them at the eye (or ear) level. The second problem was overall lack of "weight" in the sound. The target curve was definitely asking for some adjustments.
The first problem is a consequence of the fact that any virtual source, for example a rendering of the singer's voice, which is appearing to be in front of the listener, is created by a pair of stereo speakers that are physically located on the sides. In my case, the speakers are placed even wider than the conventional "stereo triangle." As S. Linkwitz explains in the paper "Hearing Spatial Detail in Stereo Recordings", if we consider the sound pressure on a very crude approximation of a human head—a sphere—we will find that physical sources located in front of the sphere and on the sides of it create very different sound pressure distributions across the frequency range. A more precise description of this distribution is of course the HRTF. Since the two audio streams that represent the virtual central source arrive from the sides, they do not have a proper frequency profile of a center source, and as a result, the hearing system places this virtual source higher. A simple solution used by Linkwitz is to apply a shelving filter which compensates for this effect.
And the second problem—overall lack of weight, or a bass-shy presentation from a flat target curve can be explained by the interaction with the room. Running a bit ahead, below are comparisons of the speaker quasi-anechoic response (FDW windowed) vs. the steady state room response, obtained from the same measurement position by taking an RTA measurement of pink noise playing continuously:
We can see that the room "eats" the bass but amplifies high frequencies. That's why adding more bass to direct sound as well as tapering the high end seem to make sense. So after some experiments with well recorded tracks, I have chosen the following target curve:
On this graph it is compared to the initial "tapered flat" crossover curve.
The Final Correction and Measurements
The final step in the tuning process is to apply "Room Macros" to the entire speaker using the target I have created. This time I used the "Psychoacoustic" smoothing. This step fixes any remaining discrepancies in the levels of the drivers. Below is the FDW response of the speakers after applying the correction, overlaid with the target:
And below is the phase response of the speaker—as we can see it is indeed close to the "zero phase" (this is also the windowed version which excludes phase deviations due to reflections):
I checked the group delays by using the "ICPA" function of Acourate ("Room Macro 6"), and found only one very high-Q group delay deviation, not worth correcting.
The step responses of the speakers look good:
Note that these are responses without any windowing, so they do not look fully identical due to reflections and asymmetry of the room. It can be clearly seen from the Energy Time Curve (ETC) graphs produced by RoomEQ Wizard (REW):
Since this is a small room, strong reflections start appearing quite early, but it's hard to do anything about that because there are windows behind my listening position—I can't put any acoustic treatment there.
Also using REW, I checked the distortion measurement and observed the known issue with Seas FU10RB drivers of the raised 2nd harmonic distortion level between 1 and 2 kHz, also noted in the "Erin's Audio Corner" review when he was measuring the LXminis:
Also there is a bit more distortion between 300–500 Hz probably because the full range driver is being pushed harder. The distortion in the right speaker around 100 Hz due to an interaction with a room mode—if I move it to a different position, this peak disappears. And I'm not sure why each harmonic trace ends up with a funny upwards curve—this must be a measurement artifact.
The resonances from room modes can be seen on the spectrogram:
I decided to order some more bass traps, will see if they actually help to reduce the effects from room modes.
Does Non-Ideal Summing Induce More Pre-ringing?
Now let's try to get back to one question from the beginning of the post. Recall the simulations of non-ideal summing of the acoustical linear phase crossover and the associated pre- and post-ringing. I decided to check what happens in reality. For that, I have moved the measurement mic by 17 cm to the right and re-did measurement. Below are the resulting step responses. This one is for the left speaker, overlaid with the original (where the crossover components are time aligned):
Note that since the causal part of the IR is dominated by the room reflections it is not possible to judge the effect on post-ringing. As for the pre-ringing, it seems that it is actually lower in the IR recorded from the microphone position shifted off the perfect alignment.
And this is the right speaker:
We can see that for this one there is indeed a bit more pre-ringing. Evidently, the real acoustic behavior of speakers is much more complicated than these ideal models. And for a proper evaluation of the crossover behavior off-axis an anechoic chamber should be used.
Does this all matter? Maybe not so much, after all. Anyway, there is no ideal solution when we are trying to combine a full-range speaker from several band-limited drivers. If we are striving to get a perfect solution, we actually need to avoid using crossovers at all, by using a single driver, for example, an electrostatic panel or the Manger Transducer. The Manger seems to me like a variation on a coaxial driver, however due to use of a single, specially engineered diaphragm it probably does not suffer from the Doppler effect. Anyway, that's a different price level.
To Be Continued
Of course, it's interesting to discuss how this setup sounds like, however this post has already ended up being quite long. I will write about listening impressions and other things separately.
No comments:
Post a Comment